Advances in Engineering Innovation

Advances in Engineering Innovation

Vol. 8, 28 June 2024


Open Access | Article

Research on optimization ideas and paths of China's UAS standard system construction

Guangcai Liu 1 , Junguang Wang * 2 , Zhangping Li 3 , Yijun Ma 4
1 Civil Aviation University of China
2 Civil Aviation University of China
3 Civil Aviation University of China
4 Civil Aviation University of China

* Author to whom correspondence should be addressed.

Advances in Engineering Innovation, Vol. 8, 81-87
Published 28 June 2024. © 28 June 2024 The Author(s). Published by EWA Publishing
This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Citation Guangcai Liu, Junguang Wang, Zhangping Li, Yijun Ma. Research on optimization ideas and paths of China's UAS standard system construction. AEI (2024) Vol. 8: 81-87. DOI: 10.54254/2977-3903/8/2024084.

Abstract

As a leading industry of low-altitude economy and an emphasis area of consumer goods trade-in, in recent years, the Unmanned Aircraft System (UAS) industry has successively received the attention of the Standardization Administration of the P.R.C, the State Administration for Market Regulation and other departments, which have all emphasized the importance of giving full play to the leading role of standards. Up to now, the construction of China's UAS standard system has made great progress, and 126 key standards that are urgently needed by the market and support supervision have been formulated and revised in a timely manner, but the following problems still exist: the standard terminology is not yet unified, the way of prioritizing the formulation and revision is too simple, the content of the standard system is still imperfect, and there is a lack of a unified public service platform for standard information. In order to solve these problems, this paper combines the new international standardization construction experience of the European, the United States and other countries, and puts forward the corresponding optimization ideas for the construction of the UAS standard system, so as to promote the healthy and orderly development of the UAS industry.

Keywords

UAS, international experience, standards system, policy optimization, digitalization of standards

References

1. Xinhua. (2023, December 12). Xi Jinping delivers important speech at central economic work conference in Beijing. The State Council of the People's Republic of China. Retrieved March 20, 2024, from https://www.gov.cn/yaowen/liebiao/202312/content_6919834.htm

2. General Administration of Market Supervision. (2024, March 27). Circular of the General Administration of Market Supervision and Other Seven Departments on the Issuance of the Action Program for Hauling Equipment Replacement and Consumer Goods Replacement by Standard Improvement. The State Council of the People's Republic of China. Retrieved April 13, 2024, from https://www.gov.cn/zhengce/zhengceku/202404/content_6944404.htm

3. National Standardization Administration Committee. (2021, October 18). Circular on the Issuance of the Guidelines for the Construction of a Standard System for UAS (2021 Edition). National Center for Standardization Engineering. Retrieved October 13, 2023, from http://ncse.sac.gov.cn/xw/sytz2021/202110/t20211018_348142.htm

4. Mai, L. (2018). Method for optimizing standard system. China Standardization, (07), 58-65.

5. Li, M., Li, Q., Zhao, L., et al. (2016). Optimizing the soil environmental protection standard system and suggestions. Research of Environmental Sciences, 29(12), 1799-1810.

6. Fu, G., Dong, J., & Pan, X. (2020). Optimization of industrial building standard system: Taking assembled concrete structure as an example. Journal of Civil Engineering and Management, 37(01), 37-42.

7. Niu, J., Liu, S., Wu, F., et al. (2022). Research on optimization of standards system in operation field of nuclear power plant. China Standardization, (05), 105-110.

8. Ji, C., Cheng, X., Luo, H., et al. (2022). Study on the meteorological standards system in the context of high-quality development. China Standardization, (17), 80-87.

9. Zhao, Y., & He, G. (2020). Analysis of the current situation of the watch standard system and optimization ideas. Time Square, (06), 100-103.

10. American National Standards Institute (ANSI). (2023, January 1). Standardization roadmap for unmanned aircraft systems V.2.0. Retrieved October 13, 2023, from https://share.ansi.org/Shared%20Documents/Standards%20Activities/UASSC/May_2023_ANSI_UASSC_Roadmap_v2_Gaps_Report.pdf

11. American National Standards Institute (ANSI). (2023, January 1). ANSI frequently asked questions. Retrieved October 13, 2023, from https://www.ansi.org/standards-faqs#ansi

12. Wang, Y., Shan, J., & Gao, L. (2021). The evolution of American international standardization strategy and its enlightenment to China. Quality Exploration, (3), 9-14.

13. Xu, B., Du, D., Liu, J., et al. (2018). Development history and latest progress of Japan standardization strategy. Standard Science, (10), 6-10.

14. Liu, X., Wang, Y., Du, X., et al. (2021). Development status and trend of standards digitization. Strategic Study of CAE, 6(06), 147-154.

15. Yuan, W., & Fang, L. (2024). Standards dialogue: Milestones and practices in the digitization of standards. China Standardization, 03, 6-29.

16. American National Standards Institute (ANSI). (2023, January 1). Gaps progress report. Retrieved October 13, 2023, from https://share.ansi.org/Shared%20Documents/Standards%20Activities/UASSC/ANSI_UASSC_Roadmap_V2_June_2020.pdf

17. State Council of the People's Republic of China. (2015, March 26). Circular of the State Council on the Issuance of the Reform Plan for Deepening Standardization Work. Retrieved October 13, 2023, from https://www.gov.cn/zhengce/content/2015-03/26/content_9557.htm

18. Xu, C., Ying, Y., Cheng, Q., et al. (2022). Research on the construction of standardized information service platform to serve local characteristic industry. China Standardization, (5), 172-174.

19. Chen, H., Qiao, J., & Pang, J. (2014). Planning order of local standards based on entropy theory. Transport Research, (3), 65-67.

20. Zhang, Z. (2014). Planning order of local standards based on clustering analysis method. Transport Research, (12), 169-172.

21. Qiao, J., Zhang, H., Wu, Q., et al. (2017). Timing model of local technical standards revision for highway engineering. Transport Research, (1), 1-7.

22. Qiao, J., & Cheng, C. (2018). Transportation standard preparation sequence based on improved VIKOR methods. Journal of Chongqing Jiaotong University (Natural Science), (5), 65-70.

23. National Standardization Administration Committee. (2023, August 6). Interim provisions on the adoption of group standards for recommended national standards. Retrieved March 4, 2024, from https://www.samr.gov.cn/bzjss/zcfg/art/2023/art_2e69a695fc574a5dbe8904761549ad8d.html

24. Civil Aviation Administration of China (CAAC). (2022, August 22). Civil UAS development roadmap V1.0 (Draft for comment). Retrieved September 22, 2023, from http://www.caac.gov.cn/HDJL/YJZJ/202208/P020220822615871900321.pdf

Data Availability

The datasets used and/or analyzed during the current study will be available from the authors upon reasonable request.

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License. Authors who publish this journal agree to the following terms:

1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.

2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.

3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See Open Access Instruction).

Volume Title
ISBN (Print)
ISBN (Online)
Published Date
28 June 2024
Series
Advances in Engineering Innovation
ISSN (Print)
2977-3903
ISSN (Online)
2977-3911
DOI
10.54254/2977-3903/8/2024084
Copyright
28 June 2024
Open Access
This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited

Copyright © 2023 EWA Publishing. Unless Otherwise Stated